DJI FPV Drone Combo Review Part 1 IN-DEPTH + Motion Control & Fly More KIT (unbox, Ustawiać, Aktualizowanie)
It finally came out. I’Ve been on spring break, so this actually came in before i left and i didn’t get a chance to bring it with me. Dzisiaj. We are going to be starting the series, jak widać tutaj, i’ve got the full combo kit. I’Ve got the motion. Controller and i’ve got the fly more kit, which gives you two extra batteries, and this uh this little multi charger here, there’s also some brace arms you can get for the drone, if you think you’re gon na be doing like close proximity really hardcore flying so like I always do we’re gon na get really in depth into this kit. Uh. This video is just gon na, be the unboxing taking everything out, seeing how it looks really close up. We’Re really gon na zoom in and check the parts we’ll boot it up on the screen. I’Ll show you how to do updating we’ll, show you how to do getting everything up and operational, and then the next video we’re going to be going outside doing our initial test flight, then we’re going to be doing range tests, we’re going to be seeing what kind Of cinematic video we can get and just how far we can push this thing, how hard we can push it in the reviews to come so don’t miss the series subscribe right now and let’s get started: Muzyka, w porządku, guys so, first off um. This is not a cheap drone.
I mean this thing cost me. I think it was eighteen hundred dollars altogether that’s, including the fly more. The motion controller, where you can fly just with this motion controller by moving your hand around and stuff and then, Oczywiście, the full combo kit since i’ve been doing this for a while. I like to show like my first reactions to things you know and um that’s, usually the most pure kind of reaction you can get with somebody with some experience with drones, and you know what also might help you, if you’re confused on how to open the box Up a little bit tape there a little tape there, and what does this thing do? Let’S see? Oh it’s got one more piece of tape here, so they really seal this good. Even the box that was shipped in they had that tamper proof. Tape. Dji is really good at making sure nobody tampers with your products, looks like we’re gon na lift these things up. Pierwszy, there we go and then the whole top there’s another view of the drone. If you wanted to see what that looks like on the front of the box that’s how it’s gon na be flying straight, pretty interesting huh, they almost made it like a plane drone where you have these kind of air foils here on the arms they made them. Like tear drop anyway that’s kind of how it looks when it’s facing full forward so it’s a pretty aggressive, looking uh product here and let’s flip this open first time viewing with you guys let’s see what we got and check this thing out guys.
So we have just right: on top, we have the v2 goggles the differences between the v1 and the v2. I think it’s just mainly internally, better electronics, but the goggles. They really look just exactly the same on the outside nice little protection stickers there and it says warning, keep the lens away from direct sunlight so of course, i’m having a little bit of difficulty. Taking these off but let’s, try again there we go there’s one boy. This is like a little challenge more challenging than i thought there. We go so don’t point those in the sunlight, jego. W porządku, if this side points in the sunlight but never point those in the sunlight, so it looks basically the same um. Even the padding and everything looks the same. Of course now you can buy alternate padding for the goggles, but anyway version two goggles a little bit different inside, but the outsides look exactly the same as the old ones. The only other thing is the drone itself, so here it is, and i got ta say my goodness: this thing is heavy holy smokes. This thing literally feels like it weighs a couple pounds i’m not kidding either. This is a heavy product here for a little race. Drone and look at that they have the battery already preset pre installed. This thing looks really radical, really striking pretty amazing and remember what i was talking about like these arms are almost like wings, see if we can get in here, just a little bit closer and really look at that shape.
So it’s it’s, almost like an airplane wing like a small airplane wing. You see how this one’s pointing more that way, and then this one is pointing even a little more up than the back. So you’ve got a really interesting wing arm design, i’m thinking that’s. The reason why this can fly so long they’re, claiming this thing can fly for like something like 20 minutes or something and that’s, pretty unheard of for, like a high powered race, drone and so we’re, getting a little bit of lift with these wing arms here anyway. Guys before i get too far into this, i mean it just feels like such a solid and heavy thing like it. Won’T even fly, but you know it will some sensors on the bottom there we’re going to get way more in depth in this. I just want to put this down and i want to go more into the box before we get too far into the drone here’s everything else in the box, so we have pair of propellers pair of propellers b, so that was a this is b. Tutaj. Is the controller so dji’s new fpv controller introduced with this fpv drone? Never before seen extra top shell goggles antennas headband for the goggles, a cable and the manuals are in this one: ac power, adapter and the goggles battery all right so i’m gon na put these on the side. We got our propellers and all of our extra accessories.
Here and let’s just really check out this drone first and check this thing out so there’s, the motors there’s. Nie, writing on the motors it’s got quick release props with a spring here right on. There see that spring counterclockwise and clockwise right, they’re gon na be diagonal for quadcopters or multi rotors, and there is just cooling heat sinks all over the place. On this thing, look at this aluminum or magnesium. I know dji drones use a lot of magnesium in their products and for weight and i’d assume. This is magnesium uh and over here, look at all these just littered with um hex screws all over the place. Even under the plastic, you can see all these hex screws really interesting. Let’S just get really close up here, so you guys can see all this stuff there’s. The gimbal cover really cool. Looking gimbal cover forward obstacle of wedding sensors. So if you guys were new to fpv, you know this might be the drone for you, because i i heard if you’re in, like beginner mode, easy mode, it will avoid obstacles uh that pop up in front of it. So you know if you’re learning how to fly fpv. This may be a good one for you just turning it around another vent and heat sink right here, so that’s going to either be that aluminum or magnesium there up at the top, airflow, probably flowing through the shell, all the way to the back and man.
This i’m, assuming this battery, is going to take up. Most of this thing, it’s going to be most of the weight this thing’s already fully plugged in so from the box. Look at this is the plug in the back it’s, already completely plugged into the drone. Um and let’s just take this battery out so there’s these tabs on both sides that we’re gon na push and it just pulls right out so yeah. The battery is just about half the weight. Jest to: just got really light here’s the battery here let’s check this out for a second. Więc, Oczywiście, they’re gon na make everything a lot more durable with this kind of drone than their other drones, because this is meant to get aggressive, close proximity to things, so you can see how they encase the battery in this pretty hard plastic frame. Nothing really to it, except for this little cable clip that pushes in it’s almost like a proprietary, xt60 kind of connector. You see that there, where it has kind of rounded area on the right, and then this is more of a flat area on the left there. If we’re, looking straight at it, let’s flip this battery around man, it’s really microscopic but i’m gon na see. If i can zoom in and give you guys a little bit of a picture of this okay so trying to zoom in here and guys. This is a 6s battery, tak 22 akumulator woltowy, pretty amazing they’re going for a very high power, 6s battery here and that’s, because you get more power, efficiency, the higher voltage you go and also, Oczywiście, you get more of that.
Uh punch right. So if the drone needs to really move around obstacles and punch, left and right up and down, you’re gon na be able to do that with a high powered battery like this – and this is also 2 000 a milliamp hour. So you know when you have multiple cells, so there’s six cells stacked up in here your voltage goes up, but your actually capacity doesn’t go up, because these are all in series, if you’re to put them in parallel, then you’d have more capacity so that 2000 mah Would go up, but your voltage would stay low, so they chose to do a small capacity, 2000 milliamp godzin baterii, which isn’t really small for race drones. But you can see how big it gets when you start putting them into series and upping the voltage. W porządku. So pretty amazing radical change in battery technology from dji there’s, a couple of things on the craft, a couple of stickers so i’m going to remove these. This just looks like a little protection sticker. You want to take off when you’re, taking off that plastic gimbal cover on the top and anything else i’m, seeing a couple of stickers here on the arm. So we have a b here, Czyli, just to tell you which propellers go where so the b propellers are going to be on the black top motors and then the a propellers that make it real, simple are going to be on those red notched top propellers.
So pretty simple to understand that so you’re going to want to take all these stickers off, ponieważ, of course anything if you leave these stickers on is going to create some kind of drag when you’re flying and you don’t want that that be happening. You just want the thing to be as efficient and optimal while you’re flying as possible. W porządku, so moving on let’s just look inside the battery compartment, real quick, so again, that’s where the battery is going to plug in and it has kind of that flip down plug. We were looking at over here on the battery, so you don’t always have to have it plugged in, but you can have it inserted and how we’re inserting very simple, just basically pushing it in like this, the notches all line up so once you just get it Right in there – and you push it just really clicks, and i kind of like that, how you don’t have to plug it in right away and put power into it. If you don’t want to it kind of surprises me that actually this was plugged in from the factory it’s kind of interesting, usually with dji batteries, you need to charge them once before, they’re even active. So if i push this little guy here, this is a little battery indicator. You see how nothing’s coming up, because you need to do an initial charge before they’ll, even power on. If you see how, if i push it in without a click, it feels like it’s kind of in, but it will just pull right out, so you want to make sure you give it that extra push and give it a tug, so you’re not having your battery Fly out in mid flight, while we have it on this angle, let’s just spin it down a little bit, so we can get a good view of all these sensors.
So this is going to be an led light here. Let’S see this tri sensor little cluster here led light, and then these should be laser sensors and then these are two downward optical sensors wow. So look at all these guys. We have on the bottom kind of, like their other camera drones, są one, really kind of going. All out with this thing so front obstacle bottom obstacle on their optical sensors. So these are actually cameras and then we have our laser for kind of like range from the ground and then our led light again then we’ve got all of these uh like i was saying, hex screws everywhere. So this looks like it’s going to be easy to work on kind of easy to pull things apart. Um so we’ll just do one more revolution here: sprawdzanie ono na zewnątrz, got a little dj logo on top and then we’ll start pulling things apart. Więc to jest, basically it in a nutshell – and all we need to do now is take off this front cover. So that’s done by what, by just pulling this that’s it so nice and easy click, pulls that off zoom in here take a little bit of a closer look, and this does have some side guards here actually on the bottom. I guess that’s just for shipping, maybe rubbing against the plastic. So peel. This thing off actually goes all the way around. W porządku, all the way around and there it is so 4k 60 frame per second camera built in so probably using some of the same technology as their osmo action.
Remember the osmo action. I did do a review on that it’s, a waterproof all in one camera. Oczywiście, this isn’t going to be waterproof on this craft, but i’d. Imagine it’s going to be using some of the same technology as that camera, because that is a very large lens kind of neat. It’S got this little protection hood over it in aluminum. The camera is not going to go side to side, so there is no. I guess that would be pan stabilization. I would imagine there’s going to be a little bit of electronic stabilization in there to dampen the left to right. But the f up to down does have stabilization, see that so you’re going to be able to tilt that, probably as you fly, and it will also maintain wherever you keep it. As the drone kind of goes like this, so we’ll see how that all works in our flight test, but pretty amazing. Looking camera pretty nice nice job there, so there’s a little thing guy here, a little door that just pulls down. You can kind of pull it out and you see those two little uh rubber kind of tabs that are holding the door on so the door. Doesn’T fall out and in here we’ve got two slots. Po pierwsze, we have a usb type c and there’s our memory card slot, so full on board. Recording you just slap your sd card in there you’re going to want to use a high speed, Karta SD.
I always have it linked down the description of what i use, so you don’t have any glitches. I use a high speed, sandisk quality 4k pro card and all of my dji drone, so you don’t have any possible glitches with using the wrong card. You just want to use the best you possibly can so there’s your two ports, there pretty cool and that just closes up just like that. The tabs slide in and then you snap that shut a little dji logo there too, on the sensor. Cluster it’s, like this whole black plastic cluster, that is just bolted right up to the bottom, tam jest, probably a ribbon cable going into the drone into the main flight controller, but um that’s, really all there is to it guys, światła LED, really neat on the backs of The arms and on the backs of the motor pods there’s the feet the feet do have. I don’t think i touch base on this. Yet if you do have this little rubber kind of molded in notch here, you can see the separation between the rubber and the plastic, so that is on the front, nothing on the back, because it’s actually sitting on the battery when it’s sitting on the ground and So the battery, if i leave this upside down, the battery actually has the back feet rubber. So this is two little tabs of rubber that it’s gon na sit there on the ground, that’s molded right in to the battery.
I remember with the fly more combo. I got back there. I got two extra batteries, so i’ll have three total plenty of flight time. If this thing flies for like 20 minutes per flight, then man you’ve got like an hour of flight time, so very comparable to some of their other. Even just camera. Drones and i’m, attributing that to just how efficient they’ve got in their design and also these little winglet kind of arms. Like i was saying before very very interesting putting in the battery and there you go, you can see how it sits on this rubber feet here and the battery down there when it’s on the ground ready for action. So i think that is pretty in depth in actually just inspecting. The drone here is the gimbal cover we’ll just pop this back on see how easy it is to get on and then we’ll work our way into the other stuff we got in the box. So i’m going to push the kind of the top in first and then let’s see how this works. Push the bottom nope we’re going to want to make sure that camera is straight there we go so make sure the camera kind of slides in to the notches. Pierwszy, i think i was like torquing the camera in there and then i have the top pushed all the way up so it’s kind of flush and then the bottom just kind of clicks. In there we go or just push it all at one time and everything kind of clicks in there so will not really come off until you squeeze this see how that kind of just a real light, little notch squeeze and there goes and it’s back on there.
So i’ll always put that on when you’re patching packaging it up and not racing it. So you can protect that pretty cool looking camera, okay guys so bear with me. Moving on. As you know, my reviews are very in depth, so you’re going to be here for a while, so might as well make yourself comfortable just so. You know what you’re getting when you’re spending this much money on a pretty amazing product like this little leds there to. Let you know how much the controllers charge let’s go ahead and press that half charge shipped and again i was mentioning the lanyard c1 button. These are pretty cool kind of like their other controllers. They have the little sticks in these little rubber grommets inside the arms. Easy access – these are a little thinner than their other uh kind of mavic, drones and stuff and mini drones. So you see that little screw. These are thin, faceci, so be careful with this. That just goes right into the gimbal screws. On give it a little bit of a tighten there and uh i’d. Imagine they’re probably giving us an extra pair of these, so you could lose these in the grass a little easier because they seem smaller than their other drone. Little separate sticks so see how we’re just screwing both of those on and there you go. So everything is spring loaded. You see that everything’s snapping back. Jeśli chcesz, you can go into here and you can take or loosen the spring or take it out, and so you can have kind of a no spring throttle like you do on most race drones, but this um drone also has gps in there.
I forgot to mention there is gps in here, so it has a return to home feature. You panic, you lose it. You go out of range. This thing will come right back and land where it took off uh. If something like that happens. Oczywiście, if you crash into something good luck, you know that’s on you, but it does have that return home gps, just like their other. You know high end camera drones or even their littler ones, like the mini and one and mini 2. That i’ve done a lot of reviews on so there’s the usb type c connector right there for charging and back over to the bottom. There is a nice vent here for ventilation, rubber grips here. Everything feels really fit and finish just like all the other uh products do for dji here’s the antenna. Do you see that there so it’s like a little spring load pop up? Więc, Oczywiście, this controller can be used and also we’re going to unbox this one. In just a little bit remember the motion controller. You don’t even have to use this. You just use that thing and fly it by tilting your hand and stuff. So this is going to be the traditional style control with this little game controller. If that’s, what you want to do, but at least you have that option flipping it over to the back, do have a couple of protection tapes here and take those off, probably just for shipping purposes, so things don’t get scratched up anyway over here on the left Trigger button it’s, just a one, click return to home is going to be like a left, click in and then record or pause is going to be um.
The other side click on that button and then over here we have like a three way: switch for a new flyer. You want to keep it up and i believe, that’s what that was, and then s is like standard where you can fly faster, but you don’t have that front obstacle avoidance protection and then you have manual mode which is going to get you into the full manual. You can do flips full manual control where it takes off self leveling and all that stuff left to see if it still can possibly do like a gps return to home. That would be kind of neat there’s. Another three way switch on this side right here and this one yeah it’s also a three way so not sure what this does yet we’ll have to figure that out, but it has a click up dot in the middle and i click down so possibly like quick Camera access instead of using this guy here, so this is a gimbal roller, so it goes a little bit and then stops and clicks back just like dji’s other kind of gimbal down up and down button. We got a start and stop right here. So perhaps this is um start and stop there’s a little m there for like a manual mode icon on there. So perhaps this is starting and stopping uh manual mode and or arming the motors. And then we have our camera record, starting recording camera and possibly pictures and that’s about it.
Everything looks pretty unique, pretty packed in there. Okay next thing in the box was just the goggles right so same thing on the outside. Zasadzie, as the version one goggles there’s we’re gon na screw in our antennas, we’ll check out those that are in the box in just a second but yeah to me, it looks just exactly the same there’s where we’re gon na loop in our goggle strap on the Sides there’s a little led patch here to show you like what channel it’s on up and down buttons there. These are just kind of cosmetic on the sides and over here on the bottom, we have our usual adjustment to adjust the distance between your eyes. There you go, you can see how moving those moves it back and forth so everybody’s eyes are a little bit different, so that will help you a little bit of venting there and i think that’s, a headphone jack as well over there on the top. So power and headphone little reset switch there on the other side same as the other ones too. We got a usbc connection here and we have our little micro sd card insert. So you can record the screen on your goggles as well. W porządku, guys so before we do get to the motion controller and the flamewar kit over there. I do want to unbox the stuff that all came in the main package with the drone. You are gon na, apparently uh get the goggles and everything included i’m, Nie jestem pewien.
If they’re gon na start having a package without the goggles or without the controllers, so everything in that box and as you can see, it’s just a power brick, Oczywiście, with all this plastic all over it. I always like to take this off. So there is our power and then this looks like our goggles battery and we’ll just pop out the goggle battery. So there we go so hitting power on. This looks like it’s just about half charged and there’s the plug in usb type c, and the goggles battery is just like a 2s um it’s, almost like the battery that came in the the mini one, to jest to, Zasadzie, za 2 18 650 komórek. It feels like in here and it’s like at 7.2 v. Więc znowu, this is a thing i forgot to mention, so this is lithium ion hard cells, but the battery that comes in the drone here are lithium polymer. So remember, while i was talking about how they were stacked up into a 6s configuration, those are lithium polymer, which gives you more punch. Probably don’t want to be using lithium ion 18650 cells in that kind of high powered drone that’s why those are normally used for stuff that has a less amperage draw like a goggle battery. W porządku. So in that box, we’re missing a couple things we need to still have the plug in to the wall and the other cables to connect the battery to the goggles.
So let’s see what’s in this other box here. So i can pull this out without destroying it too bad come on. Now there we go okay, there we go there’s, another shell for the drone itself, different color kind of a lime, green shell. This might be good for uh. You know location, locating it if you landed in the grass or crash or something so you got this kind of clear smoke, shell that comes on it, and then you can also put this lime green one that’s really washed out on the camera for some reason, but All right, let’s see what else we got so that’s what i was looking for: tam jest, a usb type c, actually that’s usbc to usa, and then this is there. We go there’s the power to the goggles right there, so that’s gon na pop in right here to power your goggles and, of course they have this little rubber band on there to hold everything, and this guy here on the other end, is going to pop right Into the goggle battery there – and that is how you’re going to power on here is uh the wall plug for that charger. So a little piece of velcro on there and remember this is just gon na go right into the brick. It’S got that little figure. Eight type of deal so that plugs in there and then this little cap takes off and plugs into your wall for charging the battery.
It looks like you could charge it just when the battery’s in the drone or you can take it out. You can charge the battery direct just like this by plugging in but remember i got that flammar combo, which has that battery multi charger, so we’re gon na see how that works, see what else we got in the box here. So a couple of other little baggies there’s, the instruction manual and stuff, nothing else in there, so there’s a quick start guide here there is our disclaimer and safety is always the thickest. These are the two extra controller sticks. I was talking about not gon na. Take those out right now. This looks like antennas for the goggles, so two in each bag. These are the antennas you’re gon na put right on the goggles. Tak jak to, so you just doesn’t matter which one is which just go ahead and tighten them up screw them on finger tight, not too hard. Don’T want to break the connector on there here’s the other bag, with the other two here and same thing, just screwing them on just like this. Essentially the same exact. Look as the version, one goggles pretty much exactly other stuff. Here is another cable, and this is going to be a usb type, a female if you look in here to a usb type c on the other end, just a short short little jumper, which will enable us to take that cable there.
That came also. So if you didn’t need to go from usbc to usbc at least you can plug this in to this adapter a little small allen, wrench not going to take that out right now, let’s just make sure we go through everything. Yeah there we go. I was wondering where that was the goggle strap. I would imagine they would have put maybe some little pocket on the goggle strap by now, but there is nothing on here to put that battery on. If you didn’t want to have it in your pocket. Velcro up through the top – and this is fully adjustable – you can see how much adjustment surface there is where this can velcro all the way from here all the way down. So if you have a gigantic head, you’re still going to be able to use this. The same thing goes for the other straps, just real, prawdziwe, simple and self explanatory so from the inside out, and then just velcro them all right in very, bardzo proste, naprawdę, nothing to explain here, just velcroing and matching up and that’s it there you go. You got your strap. You still can’t charge everything at the same time unless you have another one of these cables, so they don’t give you two in the box, so you’re gon na wan na have like a usbc cable. If you also want to charge the goggles battery at the same time, or at least in unison with the other stuff boy, i know this is taking a while hang in there we’re going to get through it.
I just want to make sure i go through everything in depth, so here we go wow, w porządku, so actually we’re getting two full sets guys. It says on the box there propeller b, so we only need two of these. So awesome we got a full extra set. So two full sets. I was thinking they’re only going to give us one for some reason and then the other box. Here we want to open up, and this should be our propeller a so we need two of each okay, so i got two without the red in the middle and two with the red in the middle and then we’re putting the ones with the red in the Middle right on the motors, bardzo proste: just push down and rotate clockwise for the ones with red, see how that happened, really simple, just basically you’re just going to want to put it in the little notch to the left of the red. You see there’s these little tabs that come on the actual propellers, see that tab there on the bottom and push it over the spring shaft just like. There are other kinds of propellers so pushing down on these, and these ones are going to rotate the other way and then you let up and then double check them, so they’re not falling off awesome. So you don’t need to deal with any lock nuts, jak ty. Normally do on other race drones. Oczywiście, why wouldn’t dji have something like this right that’s, how it kind of looks with all the propellers on it ready to go so there we go as we got through what’s included in the initial big box, with the fpv dji fpv drone let’s bust into First, faktycznie, the fly more kit, because this is going to give us that multi charger and the extra batteries and then we’ll bust into the motion controller back there in just a second, tak, po raz pierwszy, opening this as well so let’s see what’s in here all right.
There’S that and then just a couple of manuals here is a couple batteries so same kind of batteries. We got with the drone just two more and then this really simple little multi charger, nothing really to it. It just has one input coming in this way. Nothing even on the other side and then that’s, where we’re gon na plug in the three batteries right there. So let’s see how that works. So there’s our power, brick remember that came in the main package and we could either charge one battery on this. But in this instance, we want to put it in just match up the angles. Can’T put plug this in the wrong way, match up the angles, and then we’ve got these nice little notches on the sides here and it’s already lined up the right way. As long as you put the battery in these little concave notches with the connector on that direction, and all we need to do look at this is plug the batteries in just like that. So this is the one that came with it right there, and these are the other two that came with the more kit. None of the batteries are showing any power because they all need to be fully charged before our first flight. This is very industrial. Look at this it’s, very industrial looking and um. I really like how they have these these connectors with this kind of floppy, cable here uh this looks very industrial and durable.
There is a little led light right there, so you can make sure your charger is on. It does have these little rubber feet, so you can either. Tak myślę, put your batteries like that or lay them down. If you wanted a little less slidey that way, because it’s touching the rubber feet on there, but it doesn’t really seem like it matters. Whichever way you put it, you know you can put it any way. You want as long as these things are all plugged in nice and tight okay, guys moving on to the next item. I do indeed have those three batteries on that power hub multi charger charging up, and they do indeed charge one at a time. So those are charging while we open up our motion. Controller now again have not opened this at all. Yet let’s take off this plastic. This kind of was really interesting to me um. This might be good, for you know like beginners as well, because if you’ve never like used an rc controller, maybe for people that want either one of new experience in controlling things or have never used an rc product. This might be a little more easier to get into there. We go so just opening it up, that’s all that’s. W pudełku. We just got the controller isn’t that interesting. It looks like of like a joystick, the top of a joystick flight controller. Remember those older um controllers that we used for like flight simulators, it looks like it’s like exactly that’s what that is anyway, a little lanyard here we can put on the bottom right.
Nie. Uh let’s check this out little usb type c. If we unclip that guy. This is just gon na, be the instructions on how to use the motion controller so, but let’s just see like really inspect this thing close up and see what it’s all about. So i have this button here now this is uh just one push in and on the right side it says break so so you’re flying this thing around hit that and it should just like stop, i guess in the air. We have a button here for power. If i press it let’s see if we have any power on this thing, yep this one looks like it’s about 60 percent charged. We have this little joystick here m, więc jest, just a one push in now remember this thing has like a gyro inside so you’re going to be flying it turning left and right, so it’s kind of going to be like like an airplane type of flight and Then lock so have to see what that means. Lock there tilt that’s, Bardzo fajne, so possibly tilting our camera up and down, while we’re flying and then recording so starting to stop recording our video excel right on the side of the trigger plastic here, and it has a spring load here, so slow speed. Hopefully too fast so guys, this looks like it’s going to be pretty darn neat. I just opened up the instruction man manual just to see what’s up so it’s, almost like you can twist the controller here’s the controller on the right and here’s the instructions.
So you can twist it like this or move it like this and that will kind of adjust the yaw. The next segment down is like tilting the controller up and down like this, and all that is for it looks like. Is the camera that’s pretty cool? So you can tilt the camera up and down just by moving the controller, so this is going to take a while to get used to right pulling this trigger here and that is going to make it go forward. jednak, you point: this thing is going there’s going to be a dot in the middle of the screen. So when you pull the trigger and you move this controller, the dot in the middle, the circle in the middle of the screen is going to be. Your center point and that’s, where the drone will fly to so that’ll be kind of cool like if we can go through obstacles and stuff just by moving our hand. Kind of like this it’ll be really awesome. Jestem. Definitely going to be testing this very thoroughly in our flight test. I’Ll probably do a flight test with just the remote controller, the handheld and then i’ll do one with just this and see how much either easier or harder it is to fly. That’Ll be lots of fun, so you may not need to put the lanyard on because this isn’t, like a wii controller, where you’re going to be slamming it and flying it around right.
But if you did want to put it on, you just put this loop through this little hole here and then uh put the whole wristband right back through the loop really easy, and you can see how that just locks it on okay, guys almost to boot. This thing up and see how it is updating and everything, but i just wanted to show you how to put these um. These are the braces right. Więc, if you’re new to fpv, you may want to think about getting these, because these will really strengthen it. If you’re crashing and um you won’t be breaking the arms off quite as easy two of these guys, and then we got this little baggie and all we got in the baggie are two screws. Now these are allen screws and i don’t even see an allen wrench in here so you’re going to need to get your own allen wrench, because that one that came with the drone that’s too skinny, and then we have two over braces. So let’s see how these go on. You want to make the open side of the holes here. You want the cups to be up facing the top part of the drone, and then all you do it’s pretty easy is slip these over. So this slips over the front and you can see how it just kind of hugs the shape of it. So you can’t really get it on wrong. It just hugs the shape of the light and everything goes up in there and same thing for the back.
You see how easy that was that just popped on, so you can see how that’s going to make it way more sturdy if you’re hitting things this way, this brace is going to brace this front arm if you’re flying like this really fast. You hit this it’ll. Also brace the rear arm from pulling apart from the front, so you just get that much more durability from crashing. Keep in mind that there is going to be a little extra weight, so your flight time is going to drop and also more drag there’s. This little slot in the back, and you can see how the bottom is kind of that opened up portion there actually is a little r in there. I don’t know if you can see that over on the front top right here, there’s a little r by that little nut. So you know that this is the right side. If you’re facing the drone out from you and there’s, this little clip tab. That goes in here see how that just pushes right in there and then the top just goes right over that actually snapped together snapped in, and you can see how that’s hugging over the arm nice and tight. We need to put the little allen screws. They give us in the package right in the bottom there and then tighten that nice and tight with an allen wrench. So if you don’t have one already you’re gon na have to get some kind of allen wrench, i can’t believe they didn’t just put one in the package, that’s kind of a little bit of a negative.
Nie, too come on dji. Just one more thing. Put a little five cent item in the package, so people can put on their braces on their drone, stop being so incredibly cheap and charging top dollar for your stuff. You can still see the lights there through these braces. I recommend definitely putting these on kind of, like you would put on prop guards if you’re a super beginner with regular drones. You know how you put on those propeller guards. Uh definitely put these on. If this is your first fpv drone anyway, guys again, this is gon na be a long one. Let’S go ahead and get uh this all linked up. We’Ll get the goggles there’s a process. You have to do where you link it to your phone and you authorize all these things on your account. So that’ll be the next step. Hang in there, we’re almost done. W porządku, faceci, you ready here we go finally getting into connecting everything up so per dji. They say to turn on the fpv drone first now i just want to explain to you that this took about 20 minuty, see how, if i push the button there to charge fully until the lights went off, take this off first always want to take the gimbal Cover off of your drones before you even power them on so i’m, just doing a quick press, the lights come on press and hold just like all. Dji drones, i’m gon na put this thing around here, so you can see it wow that was kind of crazy.
These things were vibrating, it was making the noise that things on the camera went up and down did a little self check now. What it says to do is turn on your goggles power cable into the goggle battery plug the other end into the goggles right here. On that little port on the bottom right in order to power the goggles on, we also have to press press and hold until those go all the way up. You can hear the goggle fan go on and then check that out. We already have a link, then what we need to do guys is. We need to turn on the controller, so you go aircraft to goggles, to controller press press and hold that controller is going to come up and what we should be seeing is. We should be seeing a link almost immediately. Did you see that controller blinked, these lights, stopped rapid, blinking, yellow and now they’re, blinking, green and that’s, where this cable comes into play? Remember one end is going to go into here: you’re going to want to make sure you have that dji fly app installed in your phone from the android app store or the apple store. I’M just gon na plug right in here let’s see what happens. W porządku, x hubsyn, so i also have a hubsan quadcopter app in here and it’s saying you can also use the glasses, that’s kind of cool. This is the android one plus 6t phone connect to aircraft.
It doesn’t even see it. I only can go between the mini mini 2 and mavic air. W porządku, guys let’s, try it with the ipad let’s see what happens so. You may need to borrow. If you have android, i guess maybe you need to borrow your wife’s or friends or sons or daughters. Ipad iphone let’s, see plugging in i heard a chime. Nothing is auto. Launching i’m gon na go into drones and i’m going to go into dji fly and there it is wow that was quick and easy. Więc znowu, they are just leaving us out with the android right doesn’t work, bummer update your software dji, because all your other stuff worked out of the box anyway. Getting on moving on. We have a disclaimer here, so we’re gon na have to read everything here and agree. That is a lot of stuff who’s going to read all that who knows but i’m going to agree to it. I have already my gmail is already in there. I guess i got ta enter my password. I’Ll be right back. Let me log in here and see if it does confirm account following devices will be linked. Aircraft goggles and remote controller is going to go to my email account that i have connected to dji. So you got to do this guys, activate, registering server, restart aircraft to complete activation restarting will take around 30 sekundy. It just turned it off automatically it’s, turning it back on whoa that’s great it’s, jak to jest, like a cyborg robot they’re, going for some um dramatic boot up sequence here with this one total different uh startup, chime the controller just linked up again, i heard the double Blink and activation successful done.
Dji carry fresh okay, so now this pops up now, i could possibly see getting this for this drone. Since this is a race drone fast, you can really get in trouble. You’Re going to be wanting to push the limits going close to the ground, flying close proximity to things you might want to go ahead and get this dji carry fresh because they know you’re going to be taking more risks with a race drone right. So if i click more it’s going to take you to the dji refresh site, and so you can get that if you want to let’s just go yeah so it’s it’s 199, you see that they’re 199 dollars for one year so up to you. W porządku, if you want to have two replacements, um go ahead and you know pay the 1.99. If you think you can do without then just cancel it so i’m, going to x out on the top left because i’m not going to get this and there we go. So it kind of gives you a loop. They really want you to buy the carry fresh because they probably make a lot of money with it i’m going to cancel it. This is ridiculous. They haven’t fixed this yet so i can’t do anything except go out of the app. How ridiculous is that right? So i got to go completely out and then back into the dji app, because i don’t want to purchase the refresh so it’s, like they corral you into purchasing this so i’m back in the fly app there.
Idziemy. Look at this user feedback, no just force! You to go anything. This is ridiculous. o tak, i want to exit. So there we go see. I had to shut down the whole app to even get out of purchasing that refresh like if you kind of know how to fly. Fpv drones and you don’t want to get that let’s go through an update, so you guys know how to do this. 335 megabytes firmware update unable to take off there. You go another con with dji. Will not let you take off because guess what they force you to update almost force you to buy the dji refresh, give me a break and they’re gon na force you to update before they even let you fly the damn thing. Some of you, dji haters, are gon na love this but i’m kind of frustrated at this. At this point in time i can’t wait to fly it, but geez man. Let me pick and kind of choose what i want to do. You know the update’s going i’m going to click more tells you what it’s doing going pretty quick we’re at 15 percent and uh what’s new, while it’s updating added support for dji motion controller? W porządku. So no wonder they don’t! Let you fly it until you do this update. I can see in certain situations, yeah added ability to take off or land by pressing, lock button on motion controller wasn’t that what it’s supposed to do in the first place added tutorial videos for motion, controller and goggles.
Okay added calibration for motion controller added ability to switch goggles to dji digital fpv system. What the heck so does that mean you couldn’t use it with uh the air unit before man locking this stuff down so again kind of like early release stuff, where they should have had this stuff done before they released it, but now it’s having to update to Make everything actually work properly, um added turtle mode there you go well, that’s that’s, really beneficial. If your drone flips over turtle mode is it makes a couple of the props flip it back over. It reverses them or it just powers, one set of props and it just flips back over. You may have seen me: do it in my little fpv around the house flight go ahead and check that video will be up there. If you want to check how to do turtle mode in analog fpv drones, so that is a big bonus there, the turtle mode. Więc dziękuję, dji for doing that. Added coordinated turn to sport mode when using remote controller, coordinated turn to sport mode. Who knows what the heck that means man let’s get some like english writers in here um added find my drone under safety settings. W porządku, good good kind of like you can do with the other dji drones find my drones. That is a good feature, so turtle mode and find my drone mode. Very good added features ability to set camera exposure value manually, great optimize flight performance in all flight modes; wielki, improve transmission stability between air unit and ground unit; w porządku, mostly great um, updates and i’m glad i’m doing this update so we’re at 24 and it’s gon na Take a while, w porządku chłopaki, just checking in and getting a little bit scared.
This is why you want to charge everything up fully. I did not charge the goggle battery pack up fully. It was only less than half charge now the goggles are beeping, like it’s in low power mode. So do you hear that beeping there um the controller? Nie ma problemu. It’S got looks like about 60 do 75 percent charge, but this thing is taking forever to update. So what i might need to do is just quickly switch to this power bank. I have see on the bottom right four percent power in the goggles and it’s still going through this update, taking a lot longer than i thought it would so, but network connection required. W porządku, so that just popped up i’m going to press, ok download failed what so, tak czy inaczej. Let me let me charge this up and we’ll, try again boy so that’s, why you want to charge everything up before you even start with this thing, ponieważ, jak widać, can’t even fly or anything without doing this, and this looked like it was going to Take like an hour or more to update so very frustrated right now, but partially my fault, because i didn’t charge all this stuff up. So let me charge it all up fully, and so we can complete this update. W porządku, guys got everything charged up let’s. Spróbuj tego ponownie, so the update’s still there, even though it didn’t finish and it’s downloading, so let’s go more. Hopefully this time we don’t lose our wi fi connection.
I am connected to wi fi and everything. So maybe that was just a glitch on my home, wi fi, but just remember guys, just like all dji products, man when you first get this thing, you’re going to have to use pretty much one battery for updating. W porządku, so just basically know that you’re not going to be up and flying right away and that’s kind of the irritating thing about dji products. I guess in a way, aside from all my ranting and raving at least you’re, getting updates that are hopefully going to be making the product quote: unquote better, so i’m gon na go ahead and let it run through this update again. Mam nadzieję, że, we don’t have any more problems anyway, i’ll pop in when this thing’s just about done all right so just touching base, it seems like the controller, just restarted or beeped twice, and you can see it there with its two middle lights, flashing and that’s kind of Telling me that the controller is probably doing a firmware update as well the controller just rebooted and there it is blinking again the drone. Zasadzie, the back lights were flashing super yellow there we go. The controller is connected again we’re at 89 procent. On the update. It seemed to be installing between 10 i 15 sekundy, uh per percent there we go, saw the drone over there rebooting itself, and this should indicate kind of a wrap up here. Pretty soon. Okay guys looks like it is finally done.
I have to say that it did take about five more minutes, stuck at 91 percent rebooted the drone three times, and then it was stuck at 96 percent and rebooted the controller two times and then it finally went to 100 percent took about 10 więcej minut. The second time when it was stuck at 96 percent so really honestly give yourself like the better of one or two hours, even if you need to charge all this stuff up, pierwszy, so more like two hours when you open this thing up to make sure you Get everything updated and ready to go. The goggles now have the fpv uh back in there. You can see that before it was just a black screen when it was updating uh just saying it was updating, but it looks like we are ready to go so let’s go ahead and just um x. Z tego, it says firmware installed, fly safe requires update. So i’m going to go ahead and update this. This is kind of the network that just updates for the areas you cannot fly in like airports and whatnot dji care refresh is available for purchase within the first 48 hours of activating dji fpv. So remember: that’s kind of insurance for the 200 for two replacements make sure you do get that within 48 godziny, if you’re a beginner drone flyer that might be good for you to have for like your first year anyway, let’s just click on go fly and there We go so there.
I am sitting there with the fpv let’s turn this thing around cool there’s, our little storm trooper and other figures there at the front of the table. So what i’m going to do? Real quick is, maybe just go through some of the features, it’s kind of cool that you can see this on your ipad, so in essence you could have a dual screen set up. Let me see if i can still see it in here, yeah so i’m, seeing the set exact same thing in the goggles. If you leave your tablet or phone connected, maybe you can have a bystander watching this as you fly. Look at that super fluid too no lag whatsoever, to jest niesamowite! So if you wanted to do that, it looks like an option so we’re going to be wrapping this up now, and i just really wanted to show you guys really quick with a controller uh. What you could do as far as tilting the camera, so we’ve got this roller here on the bottom left of the controller. If you watch the drones camera over there, you see how you can roll it up and down so wow. You can go way high with it too, so i guess wherever you leave it, that’s kind of where it’s going to maintain when you’re flying.