I found online especially related to drones. Obviously so the first one here is called the ifly taurus. I guess i’m hoping that’s. The name and it’s called the x8, so what we have here is an eight inch quadcopter with eight motors two four in one esc’s that’s meant to carry almost professional grade camera equipment, which is pretty crazy and stating five to eight minutes, which we could theoretically say. Three minutes i think, but it depends on the payload you’re actually carrying here. Давайте, actually take a look at this now. The price tag is pretty hefty here, especially if you’re in europe, where you’re gon na have to pay customs after that. So here, if we’re looking at it, what we see is again, we have two 80 amp esc’s and by far this is not the recommended esc’s i would put on such a build that’s one thing: another thing is using 2806.5 моторы, which is totally fine here. Now the redundancy is true: if a propeller breaks, if a motor breaks you’re good to go, you can still fly still land, even if one esc completely blows out all four of them, Однако, depending on the type of blow blow out. В основном, if this thing short circuits everything, even the signal wires down to the flight controller, then you’re gon na have a pretty bad day. I think uh, but i think it’s a very rare case where that actually happens and uh there could be some safety features.
Some reverse protection, but i don’t think so uh. You know so um it’s, действительно приятно. What they’re doing here and i really like seeing that we’re kind of moving a little bit away from the super tiny stuff. But again this is a bit more expensive it’s. Out of my budget range that’s for sure i wouldn’t buy this. Unless i was a real professional, doing real professional work um, но да, это, i i still find it really interesting. I still would love to get my hands on this frame, though uh that’s one thing. So they’re using the 6x 80 amp esc’s now i really do hope. It has a lot of filtration on this thing, because these are always noisy and then sometimes you know on a build or two they do some weird. Иногда, if you don’t have a low easter, capacitor installed um, so you know inherently like out of the box they’re, actually pretty noisy i’m, not saying they’re bad, но это. Just something to keep in mind here and what’s. В самом деле. Nice is the integration of dji air unit. Since uh, some people will be flying that way, and here we can see that it can do a a full send. I think this is the lithium ion packs, actually that’s kind of interesting. It seems like it’s, a low power what’s. The kv on this did i miss the kv, так что это 1800 kv right here and um. Выглядит довольно хорошо, i mean i don’t know how well it’s going to be because i don’t have anything of this nature to test out, but i’m really loving the design.
You can see actually the rubber dampeners for the for the camera. Here you have, you could set up basically a dslr camera as well, что действительно здорово, and you can do quite a lot with this, since the the carrying payload is two kilograms, so this doesn’t have to be just a camera drone. It could be other things. Также, maybe for farming maybe to do some surveillance, maybe it could do just about almost anything, and i really want to kind of replicate this now i’m, really interested in how the hell did they put the motors in together, Вроде того? Is it like a standoff in the frame that takes the screws from here screws from here and kind of tighten it down um? Maybe i mean that would actually make a lot of sense, but then how the hell are they putting the motor screws in there? So there’s a lot of questions to be asked here, or it actually seems like maybe the removable, and then you put the motors and you drop that in somehow connect it and tighten it all up so i’m really curious to see how this thing plays out. I really like how it looks you have the landing skids. The design is just incredible honest. I mean uh it’s a bit complicated, but it’s actually really nice, so yeah that’s. The first thing we have let’s go ahead and move on to the next thing. Mamba’S releasing all in ones.
I actually got this one and the other one they’re on the way right now, so what they were, they they weren’t able to fit a usb in there. So they give you an adapter. You could choose, i think with one of them. You can either choose a usb type c or you can use a micro usb, so you could do that here, so it is rated up to 25 amps it’s 51 баксы. I don’t know the current price um in the market for all ones of this nature here and i’m very curious to see the size so the size here is the crazy b type board that’s. What we see right there and there are m2 holes i’m guessing after you put the rubber dampeners here using small fits which is to be expected, or anything like this filtration looks pretty decent, actually uh for a 25 amp rated one. I think this is gon na. Do uh just fine and uh we’ll get to see that as time goes on here we have a little step up with a 10 amp plus step up, and here you can actually choose if you want uh, internal or external usb, , это, pretty interesting what’s. The difference, oh okay, but why the hell did they do that? I don’t know anyway, you could decide if you want an internal or external saves a bit of weight. Наверное, but it could also be pretty annoying, and it also could be pretty useful if you could want to route that if you wanted to route that somewhere else, that could be pretty useful depending on your build.
If you have some crazy super light, build you can make it even detachable, so it’s kind of nice. I mean you can see in both ways here so it’s, an f7 35 amp bill, heli s, esc’s and again it’s a it’s, a crazy b type board. No nine volt regulator, which is kind of a letdown. Для меня, i really like the nine volt regulators on almost anything two to six s, voltage input so it’s rated up to 6s, which is really nice now iashin they’re stepping into the aio market, and this honestly seems like a what is it called jhmcu? You know that company i forgot what it was called, but it does look like it’s their design. It carries the same font, style and same characteristics here i could be wrong, but it could be just a rebranded from one of those they’re. Хорошо. I guess i you know they have their hits and misses they’re still not a super well known, reliable company, but uh we see we have a 10 volt regulator which is kind of nice actually, but hopefully uh it’s good as well. You know the only thing really with these that could go bad is the noise and the esc timing, because everything else is basically identical to everything else. You know there’s no company using fake arm chips, they’re all using the same exact arm shift all using the same exact software. So just going to come down here to the timing of the esc and how well it was built and the fets that’s all it’s going to come down to and if the timing is wrong, then that’s the root of all problems and i’ve actually been researching.
This quite often, now or recently, and have come up with a couple, pretty interesting ideas and and theories. Однако, i’m still in the middle of actually researching this and actually having the proper data. So i can relay that information back to you. So this one looks pretty good uh for how much 65 баксы 25 amps with a 10 вольт. So what you’re really paying for more here than the mom buzz, is the 9 volt that’s? Really it the amperage is the same, but oh you’re, also getting bl32 ese. So it might be a little bit heavier because those chips are slightly larger. This one here, i’m still waiting to get my hands on it. I haven’t i’ve seen this quite often, but i haven’t even used it. So this is the f405 for 40 баксы. It comes with a 9 вольт, что очень приятно, 16 megabytes. Flash memory takes raw battery voltage up to 6s and it has wi, fi and probably bluetooth. I don’t know what it has exactly, but it seems to be so currently i’m guessing it’s going to be bluetooth, but i could be wrong as well um. This kind of does look like a tiny bluetooth antenna here, but yeah again, i could be wrong. What’S really nice with the mambas here is they always add. The extra safety feature like a tvs protection diode, which is a transient volt voltage suppression. So if there’s a huge voltage spike coming into the flight controller, it will suppress it and also a reverse polarity.
If that’s going in, maybe the diode might go out first or it might not even go out so that’s kind of nice here to keep in mind. We also do have a nine volt, three amp, five volt three amp and uh 3.3 volt uh, как правило 3.3 volts are obviously for the flight controller gyro and the on screen display, depending on which on screen display they’ve used yeah. They do so. We can see. We do have the on screen display and on. The bottom is basically where most of the regulators lie: here’s the tvs diode. Here we have the memory right there, действительно хороший дизайн, 37 баксы. I i think, is a good deal honestly, so here’s mamba kind of i think copying what um ifly did so here we have another 8 дюймовый. Huge ass, quadcopter frame, that’s meant to carry something pretty big. Obviously a camera here, however um this one has a lot of 3d printed parts i think yeah. So the legs are 3d printed and it’s really hard to see what it’s doing here, but i kind of like the design we see the legs, so the battery would go down here. The camera up here that’s a pretty big platform right there, huge arms, like humongous arms here so it’s. All overall is going to be rigid and i’m guessing. It could possibly fit two motors, but how the hell do they put these two motors in together that’s? Just i don’t know i don’t understand maybe i’m missing something, maybe there’s an adapter or maybe there’s a way to do it.
I’Ve never even looked into it actually. So i have no idea if anybody knows link down below whatever you think and by the way everything here is linked down below so it’s, pretty nice i’d like to try it do something with it, at least because these are pretty thick arms. So next we have the iflight full, send a pretty expensive battery, but it’s a lithium ion 3000 миллиампер, 6s lipo. Oh lithium, ion sorry, not lipo and uh. Это 76 bucks and we can see the rating is 15 в 30 c uh, which is decent for not a heavy demanding uh success. Quadcopter here’s another one 6s also, but this one is a 6 000 milliamp for your super long range stuff, and here we can see that it’s a 6s and uh two of them actually in parallel, so that’s how you get a bit more milliamp. Из этого. I should theoretically also get more amtra out of that as well, so this here is kind of interesting. The only reason i looked for this is because i recently got this in the mail and i was like okay. What do they do different? They actually haven’t done. Anything different it’s, still the old stock, one with a couple modifications uh, very little modifications which we’re going to be taking a look at it’s called the ultimate beginner drone setup, the one i got comes with the controller uh and actually a battery. So we’re going to be taking a look at that and see if it’s any good, so this one here, i really like this, but i still haven’t been able to get my hands on it.
Я, just still trying to get my hands on one. I really like the ball aspect and the protection aspect here, so that’s really cool um, so let’s go ahead and see what’s next uh. This one i put here because this is really interesting. This is a six inch frame for 31 bucks and it’s, a really good, decent six inch frame um. So if anybody’s looking for a budget or looking into building something, this would be pretty good. If you’re looking for a six inch and you’re on a budget, you can’t go wrong with this. следующий. This one looked nice just because of the price, and i hope it is not a clone of something currently in the market. But if it is, i do apologize for that, but we can see it’s a five inch, dji compatible frame here 3k and if we take a look at the arm. Size arm thickness is five millimeters, which is totally acceptable, even if it’s a piece of carbon um. But we do have a lot of sharp edges here and yeah. We have some 3d printed parts, так что это вроде хорошо, so this is kind of cool, but the style is kind of fading away. Теперь, with the whole camera mount thing, i wish it was just a flat one right there, and then we just put our own 3d printed camera mount this one here now. I really want to get but i’m afraid that this might be a clone of kebab.
One of kebabs frames not sure uh, correct me if i’m wrong here, but it does overall seem like a nice kit that’s if it’s, not a clone um 155 bucks for a super ultra white with 2004 motors from what is this diatone? Думаю, да. This kit looks pretty cool and uh it’s running uh 2004 motors with a 1700 kv 6s. They are t motors and with the all in one 20, amp gib, rc flight controller. So you’re missing is the camera receiver and video transmitter for this setup, uh and that’s about it here really uh. So yeah i’d like to check this out and um yeah, hopefully build it on the channel. We have a build up coming very soon. This one i couldn’t understand for the life of me: is it watching three channels at once, or is it just a triversity receiver, То есть, storing, uh footage or outputting footage? If anybody knows, let me know down in the comment. Section looks pretty cheap, but i don’t know how many people actually use this. So let me know down in the comment section also akk is, я думаю, trying to come back into the game. We have a new video transmitter. Hopefully so i haven’t seen anything from them in a while. The ultra long range video transmitter that has a fan and it goes up to 3000 milliwatts now is this true don’t know, but we could roughly safely assume 1500 milliwatt output power.
This is hopefully worst case scenario with this setup. Очевидно, что, this is going to take a bit more uh power to draw a bit more power, so you wouldn’t want to probably put this on a normal five inch build. Maybe one of those eight inch builds that we saw, or maybe a seven inch or something something that could actually accommodate this it’s, not that big but it’s, pretty big and it’s going to take quite a bit of power, especially with the fan and obviously the output Power here and it doesn’t even have a 5 volt regulator and it takes 8 в 28 вольт, что является своего рода хороший, but they suggest at least a 2s battery. If you wanted to power this basically separately from your flight controller uh, so it’s saying could get around 10 kilometers of range, очень приятно, and hopefully somebody will test that out there, because i don’t have the place to test that and yeah well that’s. Really it guys. I really hope you enjoyed the video if there’s a build up coming, make sure you stay tuned and also everything’s, linked down below check those out it’s great support, channel and come join. My patreon there’s gon na be a lot of awesome, cool new things in the upcoming month and well.