5 inch micro quadcopter, which is equipped with the codex nebula pro digital transmission system. In this video i’m going to quickly go over its features and specs show you how to set it up. Give you my feedback after testing it out and wrap up this video with some flight footage. Tout d'abord, the emacs babyhawk 2hd is available in a couple of versions, which only differ into bundled radio receivers. You can get a plug and play version and then install your own radio receiver or use the dji radio controller, and you can also get versions that come with pre installed, airfryer sky d8 or crossfire nano ready receivers. en outre, even though the flight controller features a built in osd chip, which makes it compatible with analog vtxs, currently, the babyhawk 2hd is only available with the kalix nebula pro, so it is only compatible with the dji hd ftb goggles. As for packaging inside the box, along with the quadcopter, you are getting some stickers: an emax branded battery velcro strap the user manual of the codex nimbulla pro and a bag with some spare screws, spacers and nuts. en outre, the user manual is available online and you’re. Only getting a single set of the emac schematar 3.5 inch propellers, and especially because these are non standard, propellers in case you’re, going to purchase the amx babyhawk 2hd. You should make sure to get some extra sets. As for its packs, the imax babyhawk 2 hd features the imax echo 1404 3700 kb motors, which can handle up to 4s batteries when pushing the emax kimiter 3.
5 inch propellers on the center of the frame, you can find a whop style 25.5 par 25.5 Millimètres. All in one flight controller that features an f4 processor, cam pre flashed with bit of light 4.2.5 and features an integrated 25 ampere bles. Four in one esc, une 35 volts, 470 microfarad capacitor is pre sorted to the battery pads and the battery is going to be mounted on the top plate and connected to the flight controller. Using an xt 30 battery connector, the codex vista is mounted to the top plate using 20 par 20 millimeters m2 mounting holes. The rush fpv cherry antenna is mounted on the back of the frame and secured in the following manner. The enabler pro camera unit is mounted on the front of the frame using 3d printed tpu parts under the all. In one flight controller, you can find a transparent plastic sheet which is going to help to protect the flight controller, especially for water damage, which is helpful in case you land on wet grass. The wheelbase of the frame is 154 millimeters and it features a wide x pattern. The thickness of the bottom unibody plate is five millimeters. The thickness of the top plate is two millimeters. The distance between the bottom and top plates is 22.5 millimeters and on the bottom plate you can only find 25.5 par 25.5 millimeters mounting holes. en outre, the weight of the baby hook to hd without a battery is 144.
5 grammes, including a gmb 1100 milliampere forest lhv battery, qui est celui que je recommande d’utiliser avec cette configuration. The total weight is 235.6 grams and the total weight, including a gopro 7 black naked camera and without a battery, est 181.7 grammes. As for setting up the imax baby hawk to hd first, you will need to activate the codex vista and update it to the latest available version. Then you’ll need to bind it with your dji goggles and in case you don’t, have any previous experience with the vista system and you’d like to learn more about it. You can check out my review in this link over here. en outre, in case you have one of the bind and fly versions simply bind the red receiver with the radio controller, and in case you have the plug and play version and you’d like to use it with a different radio controller than dji’s. You will need to install your own ready, receiver and i’ve installed the crossfire, nano sc receiver and connected it to uo2. You should note that in case you would like to use the dji radio controller. You might need to wire the s bus out pad from the vista unit to the s bus in pad of the flight controller. As on my version, it wasn’t pre wired. As for betaflight configuration here, you can see how the port section is configured. The reddy receiver is connected to uo2 and the vista unit is connected to ut1 under the configuration tab.
Most of the settings are set to the default values. In case you installed your own radio receiver. You should configure it and by the way, pour une raison ou pour une autre, the soft seal option was enabled, and since it is not in use, you can simply disable it. Ici. You can see the power and battery settings next under the pid tuning tab. We can see the pid related values. These are not the stock settings and i can already tell you that, as expected from emacs, this quadcopter is properly tuned under the receiver tab. You should make sure that all the sticks and switches are working properly, then define your favorite flight modes and osd elements, and you should be good to go. The next thing that i’ve done is to head outdoors and test the imax baby, hawk to hd after testing it out. Je peux vous dire que, Tout d'abord, i really like its size and i think that 3.5 inch quadcopters are going to become popular as they seem to do great in terms of performance and flight time, but still maintain a relatively small form factor in terms of Flight time you can expect between five to six minutes using an 850 milliampere like the battery and between six to seven and a half minutes using an 1100 milliamp forced lhv battery, which actually weighs almost the same as the 850mph battery. So in case you are in the market for a new battery, i recommend to go for the bigger battery which will provide you with a longer flight time.
en outre, the babyhawk 2hd could easily carry a naked gopro 7 black camera without damaging the flight performance, and i got about 5 minutes de temps de vol, which is pretty good. As for durability, i crushed the baby hawk to hd a couple of times, and it is still in one piece. The bottom unibody plate features a reinforced pattern, so it’s not going to break easily and the protection layer is a great add on on a bad crush. toutefois, you might break this quadcopter, so in case you are a beginner. I recommend to purchase an extra button plate because if one part is broken, you will need to replace it entirely, and i also think that it could have been better if the camera was positioned. Slightly deeper inside the frame, so the camera lens was better protected. en outre, you should consider getting a shorter battery. Velcro strap as the provided. One is just too long and, comme vous pouvez le voir, it got chewed by the propellers. I also recommend to secure the battery leads to the standoff using a zip tie, so in case of the crash. If the battery leads are going to be pulled, the battery pads are not going to be ripped off and for some reason, emacs kept the moto wires too long. Alors, comme vous pouvez le voir, they are just tangling, so in case of the crash they can be pulled off, so i would recommend to shorten them and properly secure them to the bottom plate.
Two more things that are worth mentioning are that, Tout d'abord, i didn’t mount the immortality antenna in an ideal position in terms of radio signal, so you will be better off mounting the antenna on the front of the frame using a 3d printed part. toutefois, i preferred this method because the antenna is better protected. The second issue is that, due to this antenna mount, i didn’t experience a very good video signal. Imax probably chose it in order to extend the lifespan of the antenna, and in case you would like to get further, i would recommend to get a longer version of the rush fpb cherry antenna so overall, À mon avis, since the imax babyhawk 2hd is fun to Fly seems to be durable and will provide you with a relatively long flight time. I think that it is suitable for both beginner and advanced pilots, and in case you have the dji hd system and you are in the market for a new quadcopter. You should definitely consider getting it i’m going to wrap up this video with some flight footage and, comme toujours, si vous avez des questions, n’hésitez pas à leur demander dans la section commentaires ci-dessous n’oubliez pas de laisser un pouce en l’avant.