What i want to do first is take a look at the things you’re going to get. If you order the cadets vista version that the analog folks didn’t get obviously you’re going to get the caddix vista instead of the analog camera and video transmitter you’re going to get a couple of camera plates and you’re going to get this kit, which has the 3d Printed antenna holder for the vista and some standoffs and some mounting hardware, and the reason you need different standoffs – is that the standoffs that come with the freestyle frame are too small. They’Re too short to hold the vista, so we’re going to need to install the longer standoffs that come with in a separate bag with the kit. So now all the smaller standoffs have been removed and replaced with the larger standoffs. We’Ll just set those aside now the quadcopter that i’m working with is actually my finished freak style, build and i’ve kind of taken it apart and taken some parts out of it to kind of rewind it back to the point where i think you’re going to be At if you’re going through this build, i do have the camera header still installed. So let’s just go ahead and desolder that, because we’re not going to be using the analog camera header when we’re using the catex vista – and you may not even have installed this at all – if you were paying attention when you went through the very first install the Other thing you’re going to notice is that i have my receiver installed.
My rxsr receiver and the reason that’s installed is because currently i’m flying this quadcopter using the freesky x9 light controller but i’m going to install this with the assumption that we’re going to be using the dji controller and the main reason i’m going to do. That is because i haven’t documented that yet so i want to be able to document it for you so i’m going to go ahead and uninstall this rxsr receiver as well. You wouldn’t have installed it at all, or if you are going to be using the free sky receiver, then you are going to leave it installed. Aquí está, the cadx vista – and i want you to get this wire harness here and we’re, going to start prepping that the cadx vista wire harness comes with a plug and if our flight controller had a plug pre installed for the dji system, all we would have to Do is plug this into the flight controller and saw we still have to solder. These ends to the vista, but we would be good to go. Por desgracia, the xylo stacks flight controller does not have a dji plug so we’re going to need to just cut this end off and direct solder. Both ends of the wires now i’m going to take the caddix vista i’m actually going to flip it upside down. So i get better access to these solder pads right here in case you’re wondering this. Blue putty is called blue tack and you can buy it on hardware.
Drugstore hardware store amazon and it’s super useful in situations like this for holding stuff in place, while you’re soldering, the pads on the vista, are voltage ground, rx, TX, ground and s, bus and we’re going to be using all of those pads. If you are not using the dji controller, but instead you’re using like the x9 light or some other controller, then you are not going to deal with the s, bus and the second ground pad, but we’re going to solder. All of those up also don’t. Let the fact that there’s, already solder on your v bet and ground pad freak you out. They do that at the factory to test it. They have to solder to it to test it so i’m going to tin each of these pads and my soldering is always worse on camera, because i can’t get closer. I need a magnifier. I really need a magnifier. I can’t get my face closed down in there to see what i’m doing so, oops and we’re going to take our wires and we’re going to strip and tin these wires and i’m, not actually sure. If you’ve seen this earlier in the tutorial or whether you came straight here – and you haven’t seen this yet so i’ll just show you once we’re just going to take the wire with your fingernail. You can just strip off a little bit of the insulation you’re then going to pinch it and twist it to twist it into a nice bundle and then a little trick.
You put the soldering iron down on the table. Don’T put the hot part of the soldering iron on the table, just the base just the handle, and then you just get a little fresh solder on there to tin that wire. And then we are gon na just cut this to about about two millimeters length: Estoy. Gon na do that for all these wires, once i’ve got the wires prepped i’m gon na get my tweezers out and i’m gon na solder. The wires up it’s a little tricky to get your soldering iron in you kind of need to bring the soldering iron in at an angle to get the pad and the wire in and i’m going to show you how i do it, pero es. This is going to be a little tricky if it’s your first time out the gate, but hey that’s. What you got to do if you want that, dji goodness and when all is said and done. This is where you should be you’re, going to definitely want to double check. This pin out, especially the red and black wires. The red should go to v. Black should go to g. If you get any of the other wires wrong, nothing bad will happen. Just it. Won’T work, but if you mess up the voltage wire you could fry it. You don’t want that. The next thing i want to do is install the antenna on the vista, and the reason i want to do this is that getting at this ufl connector is a little tricky once it’s already installed, it’s just easier to do when you’re outside of the quad i’m.
Going to take this 3d printed adapter that comes with the xylobuild i’m going to feed the antenna down through. There requires just a little bit of pressure, it’s going to be a friction, fit oh that’s, Muy bien. I guess okay uh! For this particular antenna holder. We do not need to use this plastic clip. You can remove that um. That would be used for a different kind of antenna mount and then i’m going to take a 1.5 millimeter hex driver and i’m just going to remove this screw entirely. In theory, you can do this without removing the screw, but i’ve always found it really difficult and it’s just easier to just take the screw out. Then we’re going to slide this retaining tab out and getting it out is easy. Getting it back on without removing the screw is a real pain we’re going to take the antenna and we’re just going to pop it down onto that ufl connector. There we go to get the retaining bar back on i’m, first going to put it underneath this little pin right here and then i’m going to slide it over and put the screw back on so it’s, getting it back underneath that pin that’s really tricky. If you don’t take this screw off and on this side it needs to go down and underneath this top plate yeah, so you can see i’ve got it slid underneath that top plate there i’m just going to push that the rest of the way in, and you Can see it’s not quite lining up all the way, but as soon as i put the screw in it’ll all sort itself out and that’s how you want it to be with one side underneath the pin right here and one side underneath the screw right there.
The next thing we’re going to do is mount the vista inside the quad and in order to do that, i’m going to flip it upside down and i’m going to take these long m2 screws i’m going to drop them into these four holes in the in the Frames bottom plate bear in mind: we are using the inner set of holes, not the outer set and then i’m going to mount the vista and in order to keep them from falling out, you can just hold them on with your hands or maybe get like a Little piece of tape and tape over like just like that kind of keep them in place while you’re working the vista is going to get installed by passing those screws through these inner holes. Here make sure you install it with the usb port up the camera facing forward and the wires in the antenna going out the back, and in my case i have already installed the capacitor and the xd60 wires as described in the previous video. And this is going to get in the way just a little bit, but if we just lift the capacitor up slightly, it should go got it. I got it lined up i’m gon na try not to bump this camera wire too much there. We go and see. If i can get this down below the capacitor there, we go that’s out of the way nice and you can see here sort of how they’re, laying with that capacitor, just kind of rising above the top of the vista next i’m, going to take these little m2 Nuts, that came with the kit and i’m going to start to install them on the screws.
I guess i’m going to take the tape off yeah. I wish i won’t take the tape off yet i’ll, just sort of use my finger to hold it as i get those screws started, yeah perfect. Once i got all four of those nuts on there, then the screws won’t fall out. Remove that tape and i’ll go ahead and tighten this down when you tighten those nuts down, don’t tighten the first one down all the way, because the vista can actually kind of to the side so get them all make sure the vista sits flat and isn’t under Any tension when you tighten them down, but definitely make sure it also can’t vibrate or move. I don’t know if you’re gon na receive these, but my kit also came with four of these little rubber, washers and yeah. The the original kit does use those here underneath the flight controller as spacers, but my vista kit came with four more and i have no idea what they’re for, but i don’t think they’re used for anything i’m just going to save them for later for another project. The next thing i’m going to do is i’m just going to move the camera to the side, so it’s out of the way i’m going to lift the flight controller off very carefully. So i don’t pull or tug on this asc, plug and i’m going to flip. It over, i can even set it on there upside down i’m going to tin this v bat and ground pad don’t.
Let the fact that they already have solder on there uh concern you. I had done something else with this quadcopter in the meantime and i’m, going to take my red and black wire from the vista and solder them to the v bat and ground and actually before i do that i’m, just going to give them some twists together to Keep them looking nice now, Estoy, going to flip that back over again on top and i can plug in the esc, connector again as well. Next we’re going to take the white and yellow tx and rx wires and we’re going to solder them to this tx4 and rx4 pad right here. The white one is rx, which goes to tx. The yellow one is tx, which goes to rx and again i’m. Also going to twist them together just to keep them neat looking and then, si estás, using the dji controller we’re going to take the yellow and black s, bus and ground wires and we’re, going to solder them to the s, bus and ground pad here. I’Ve already tinned those you can see from the fresh shiny solder and just like the others, i’m going to go ahead and twist them together before i solder them. Yellow goes to sbus. Black goes to ground, and here is the beautiful result. Bien, it’s it’s kind of tangled up i’m, not sure you can see much going on, pero eso es. How it looks. The next thing i’m going to do is install this antenna mount on the rear standoffs, just to kind of keep it out of the way while i’m working – and i think the nicest way to do that is going to be just to rotate it in a circle.
To give a little twist and then stuff it down on top it’s got just a friction. Fit yeah, apenas como eso. Yeah seems good. The reason i like to twist it like that is it keeps it out of the way it keeps it tucked up in here versus kind of hanging out here in a u shape and but at the same time, a little sort of just a half twist, or Maybe a full circle twist doesn’t put any unnecessary tension on the wire uh you don’t want to you. Don’T want to really twist or kink or put a lot of tension on that antenna wire, but there’s a little half twist like this is no big deal. The next thing we’re going to do is mount the camera, and in order to do that, you’re going to use these two little rubber. I like to call them ears. I don’t know just seems like the right word for them these two little rubber ears, son, going to slide down over the front standoffs and then you’re going to use the original screws that you took out of the dji camera to screw through and into the camera. Through the ears and hold the camera on, there are a couple little gotchas here, number one. When you install the ears, make sure you install the ears with the ear part on the outside. If you install them with the ear part on the inside, the camera will not fit in between the the ears and the other thing is when you screw to the camera, make sure you screw to the bottom of the two screw holes on the camera here’s, the Top screw hole we’re not using that we’re using the bottom, and the reason for that is that it’s going to let the camera tilt back a little bit.
You always want a little bit of up tilt on your fpv camera so that when the quadcopter pitches forward you’re not staring at the ground after you install the camera you’re going to want to kind of wiggle left and right and get it centered up. And you can also push these up and down and get the get it level i personally like to just get it so it’s, just barely not touching the bottom plate, you don’t want it touching the bottom plate. It may pick up some vibration, but just have it low and level relative to the bottom plate. It looks pretty good to me next we’re going to take these camera plates uh, and the first thing i want to point out to you is that there is a top and a bottom to the camera plate. The bottom has a single tab. The top has two tabs and that’ll keep you from installing them upside down by accident, and those are gon na go to either side of the camera. Um they’re gon na oh philly, um i’m gon na need to raise the camera slightly. éste, the little rubber ear needs to fit in this hole, or otherwise they they won’t go in place i’m, just going to raise it up just a little bit now. You may want to skip this step, and the reason for that is that these camera plates are going to protrude out the front of the quad just a little bit.
You can see it happening right here and that’s going to give a little more protection for the camera in the case of a front end impact, but you will see them slightly in the camera and it’s going to reduce your feel. How much you can your peripheral vision? If you will so some pilots would prefer to leave that off and take their chances. Some pilots would prefer to have it on. You can go either way and, Claro, you can always change your mind later. If you decide to – and at this point the quad is basically done, obviously you’re going to need to put the top plate back on, and there may be a few other steps to do like installing this battery pad those steps. The final steps for putting it back together are going to be back in the original assembly, video but i’m going to leave it just like this, because the next thing i’m going to do is take it over to the computer. Do some beta flight setup and do some setup of the dji software and just in case anything has gone wrong? Maybe you need to re solder something it’s nice to not have to take the top plate back off again that’s how i approach most. All of my builds, i don’t button them up until the very end when i’m sure everything is working right, estamos, gon na put that stuff in another video. En este punto, this video is over go down to the video description.