Bracers for the dji fpv drone we’re, going to talk about whether they’re a good or a bad idea and we’ll take a quick look at how to install them. As there is a little bit of a trick to it, as you can see here in front of me, i have a drone already with the arm bracers installed. I actually crashed this drone with the armbracers and, όπως μπορείτε να δείτε, it is still intact. So did the armbracers prevent me from snapping off an arm who knows but let’s just jump right in and take a closer look. So this is an accessory dji launched alongside of the fpv drone, their arm bracers, as you can see here, they’re installed and the theory behind them – is that they’re supposed to give the arms a little more strength. If you follow any of the facebook groups, you can see one of the biggest comments that people say when they look at these armbracers is now you’re gon na end up breaking two arms instead of one now that could be entirely true, but my thoughts are when It comes to that is, if you have dji care, refresh it doesn’t matter, whether you break one arm two arms, three arms or all four arms it’s gon na cost, you the exact same deductible so having these arm braces on there in a really severe crash, may End up breaking two arms but on the other hand, it could prevent you from breaking no arms it’s kind of like.
If you take a popsicle, stick snap it in half you take two popsicle sticks. You have to put double the force in order to break it. Έτσι, για μένα, i do prefer to have them on just to give me that little extra piece of mind, and as mentioned at the beginning of this video, i did actually crash this drone. I flew it directly into a tree and i was in sport mode at the time and i was pretty well full stick forward. Δυστυχώς, i don’t have any video of it. I was actually just filming a little bit of b roll and i was flying line of sight. Hence why i hit the tree, but there was very minimal damage done to the drone. Φυσικά, i snapped a few props and if you look at the motor here, i don’t know if you can see that on film or not, but you can see the motors all scratched up. I’Ve got a couple. Scuff marks there on the arms here at the back. I have some scuff mark and i also have some red transfer, both here and there and i’m assuming that’s from the props rubbing up against the arms when it was crashing. I did get a gimbal error as well. I think the gimbal took a bit of a hit. I had to clean some bark out from uh from the camera there. You can still see a little bit there in the in the crevice, but the drones in one piece.
Had i not had the arm braces on there, Ποιος ξέρει, maybe it would have survived. Maybe it wouldn’t have there’s no really way to know for sure, but in that situation i was glad i had them on so i have another set here that i’m going to install to my other drone and they’re pretty straightforward to put on. Ωστόσο, there is a little bit of a trick when it comes to putting the screw in and i’ll show you that here in a minute, Είναι, not so much of a trick, but just something you got to pay attention to so inside the package. When you get it, you get an instruction booklet, basically showing you how to install it. We get two arm bracers and you can see here we get two clips and we get two little screws now you will need some form of tool to install them here. I have a two millimeter hex screwdriver, that little allen wrench that comes with the kit is too small, so you will have to make sure you have something to install them. Installation is pretty basic. If you look at the bottom of the armbracers, one says right and the other one has an l on it for left, basically with the camera facing away from you. This is right, and this is left. If you take a look at the arm braces here, we have a cut out at the front so that’s, where the front arm is going to go through on the back there’s just to cut out where the light shows through.
So all you do is slide that front leg through and at this point you just have to pop it on now. You have to put a significant amount of force and it’s almost the amount of force that you think you’re going to break it, but you do have to put a good amount of force on it once they’re on there they’re actually very difficult to get off. If you try to get them off, you can hear a lot of creaking and cracking almost so i don’t know if it’s something that you’re going to want to take on and off now one downfall to using the arm bracers. If you have a case that has a custom cutout for this drone, obviously it’s no longer going to fit with the arm bracers installed if you’re, using something like a backpack that just has an open cavity. These arm, bracers won’t affect how it fits. We just do the same for the battery. We just got to kind of force it in until it snaps in and then we’ll do the other side. So now, at this point, we’re going to take our two clips, they just fit into the back there’s a groove. There and they just line up over that screw hole now. This next part is where i said, there’s a little bit of a trick, but it’s not so much of a trick, but just something you have to pay close attention to you.
Don’T want to put these screws in from the top down. They’Ll go in and you’ll be able to tighten them up, and you think that it’s attached securely that bottom part doesn’t actually have any threads in it, it’s just an open hole. So if you put some screws in from the top down, that thing will still flop around it’s not attached in any way what you have to do is put the screws in from the bottom. So i guess it’s just a personal thing, whether you think these arm braces are a good idea or not, Αλλά, like i said after crashing this drone i’m going to leave mine on just for that extra peace of mind. I know it may not protect it in a severe crash, but perhaps some minor crashes. It will save me snapping an arm now when it comes to flight performance. I’Ve been flying this drone here with the arm braces on for a little over a week. Now and myself, i haven’t really noticed any flight performance difference. These weigh about 19 γραμμάρια. So when you take that into effect for the weight of the drone, i don’t think it’s going to affect it that much now, if you’re a person who does very technical flying, then maybe perhaps you might notice it but that’s not really the kind of flying. I do so i don’t know if i would really notice, if that’s the case well, folks that’s, basically it for this video.
Those are the arm bracers for the dji fpv drone. Hopefully you found this video informative and got some value out of it.