In short, it is a tractor quadcopter, so for beginners it is excellent because we all know beginners or even experts sooner or later, a good blow. You take a sturdy quadcopter for beginners, where you do not fear the blows. You learn much more. In reality, this quadcopter has been a subject of debate because joshua bardwell, who is an american youtuber, who deals a lot with fpv, certainly many know him had made a video without making a review saying that, according to him, it would have been better to take the Of aton and rome, f, 5 or even the i flight, nazgul 5 v2, and I must say that I do not remember at the time how much this quadcopter cost only that, in my opinion, it is absolutely not a fair comparison, because the black cat, but it Costs about 240 euros without receivers. The same also applies to nazgul. It costs 230 euros without a receiver, and so could compare with this quadcopter that the ski stars – beworm 228, which in my opinion, is a good quadcopter with better components that costs 150 euros. And this could be a comparison. But I must say that at 134 euros and with the discount coupon that they leave you, the description of the video 122 euros cannot be absolutely excluded a priori a try, a test and a review of this quadcopter, because it is much more robust. It costs a lot less and all in all with what it costs.
I would definitely recommend it to the principles, even obviously after having tried it together and especially after having seen this video, because there are some to know, let’s immediately see what comes with this quadcopter. Obviously, the propellers and the greenhouse nuts arrive re, the propellers and the propellers are still tornado, 50 46, and they give you 8, together with the quadcopter. The data are of different colors because in theory they should be two nuts, with hourly thread that go on two motors and on opposite motors. Instead, they should have a contrary thread. However, it seems that the problem is not only mine but of all the Chinese zar. 220 b2, who have the wrong nuts and therefore you cannot fit these data, do not even try to force them because they are ruined to the thread and you cannot absolutely let 2 threads enter wrong consent. So, yes, even if here it says, quality control passed and they have certainly not checked it. Otherwise they would have noticed this. So after having marked this thing of the aic nuts, nor have they told me that they will withdraw all the products that are in the market and replace the nuts with the correct ones. However, it is still considered correct to report this thing to you. In the box. We have a polarization antenna. There rcolare seems from the arrows here that it is an hourly polarization and it is a lollipop also from the shape it could be a mini pagoda.
And if you are a beginner, I remind you to immediately add the antenna to avoid connecting the battery forgetting to put the antenna and then burn the vitis wii tx. Therefore, video transmitter capable of transmitting at a maximum power of 600 1000 watts and, of course the power is adjustable, and we also have the possibility to change the band and power channel directly using the sd on the screen. Then via flight controller. In the box, we have some pins of rubber that, from experience, even in the very old model I had reviewed, with which many many made me started, lfp via precisely because it was a very cheap model that worked very well and I’m. Talking about the first cine wizard 220 and not the s version that does not. I didn’t even review it, because it didn’t fit and with feet that come off very easily and I usually wore one clamp to fix them when we even need them. Because here we have tpu protections that directly protect the quadcopter very well that I add that modulate and therefore, even if we had to break a very simple arm, detach the broken one and replace it with a spare part that is also available. This is a positive thing for beginners in the box. We also have a bit of bands a cohesive, silicone adhesive, in addition to the one already mounted on the quadcopter. It is because one mounted one not because with the quadcopter, there also comes a support for a possible gopro, and now someone can say, oh well, 1 and beginner what to do with the go pro on a quadcopter b and now at this moment on ebay.
You will find a lot of go pro 5 or 6 that cost very little. You can safely put inside this tpu support and fly and film with this quadcopter that, therefore, depending on whether you want to put a weight in front or not put a weight in front of this one, cohesive, silicone adhesive must be admitted. I have in front or behind, depending on the weight distribution, to balance the center of gravity correctly by moving the battery forward or backward in the box. We also have a carbon key to tighten the nuts and some adhesives, the cine for, as for the battery recommended by cinemas, a 1300 milan 4s per hour, which, in my opinion, is too little for the absorption of this picture and 4. Also because it is quite heavy without a battery, in fact, it weighs 386 grams and therefore I recommend a battery, especially if you are a beginner. You will have a longer duration with 1500 1800 milan for now, and the weight of the quadcopter reaches 586 g. Obviously, without gopro, certainly to lower the cost, there are some compromises that, in my opinion, are absolutely not a problem. For example, we do not have the es like most of the us that there are currently 4 in 1 of put directly under above the flight controller, but we have the classic 4 ass to put s The arms that, on the one hand, are of the old Generation are not bl e li 32, but are bl li est at 30 am x and I personally notice absolutely no difference in flight level, especially if your quadcopter has not taken a lot of blows or you have a damaged propeller in short of the components that Vibrate everywhere here we do not have the rpm filter, but if the quadcopter is fine, you will certainly not feel any difference as regards the motors are 22 07 from 2500 150 kv branded.
The cine certainly are not manufactured by the cinemas are rebranded. The camera for fpv is the fox in a row micro pro that a good camera, I would say all in all here is one thing to report, but also is that this camera has its own or sd. If you want to connect it directly to the battery and can report the battery voltage thing that is reported directly by the flight controller, in fact, as you can see, we have the double or sd. That of the flight controller is that of the camera completely useless. As well as annoying which, unfortunately, we cannot remove without the board joystick to control the camera that does not arrive with the quadcopter and in theory it would have to be bought part. I will report this thing to bangkok that maybe include the joystick with the quadcopter or possibly in the new ones samples. Maybe they will remove the sdi of the camera. Well, if you are a beginner and take this quadcopter, what do you miss to fly in fpv? Well, you miss a radio and I recommend this radio. If you want to save anyway the whole list of recommended things you can find them in flight with the sum point it and in the description of the video, you obviously also lack viewers or glasses for fpv. Even there, I leave you in the description of the video both of the cheap viewers, but also the best that there are, in my opinion, in the market currently, and obviously the receiver would also be missing.
That goes connected to these three cables or possibly, you can use the cable e that arrives with your receiver, possibly if it is compatible with this connector jst nearby wizard, 220 v 2 is provided with this support in tpu. That supports both the antenna of the video transmitter, but also possibly, if you want to mount a tbs crossfire here, then immortalized as antenna goes put here. Obviously, if one wants to save money, surely he will not take the tbs crossfire, because it is an extra expense and probably also useful to learn. It is better not to go very far. In being close, the ex are connected in the old way through a power distribution board and above we have the video transmitter below. Instead, we have the flight control a very recent parsi, f 405, in fact also the usb c connector. One last thing to report. Even if I have not had such problems, but someone complains that there is a bit of latency regarding the video transmission, I went to investigate the same and I noticed something a bit strange, as you can see here is the connection to power the vtx and these Two cables, which are the green one, that the smart audio and the yellow one that the video input and are connected correctly, while the red one is connected to the 5 volt out, which in theory should go to power, a camera. The black one is connected to the gnd that the negative that there is no problem, but this thing here but questioned so i went to investigate the other side.
I saw that the video link and smart audio link are connected correctly. On the other part, they separated with a separate connector the power supply they connected it directly to a 5 times filtered output. Only this video transmitter works with a minimum voltage from seven times up to 24 volts which the maximum, so this could be the problem. So I simply went to unplug these cables from the connector and reconnect to the original connector next to the two smart, audio and video cables, because this flight c ontrol is actually very good and a2 back, even a filtered at 9 times just suitable for the video Transmitter – and I do not understand why they went to separate them – put them in the five times then reconnected it correctly. On the other side, with the red cable, disconnected from the 5 volt outlaw connected to 7 24 volts that the correct connection and the gn of I put it next to it. And obviously I connected a receiver and I had a rx sr of the fr sky. But you can choose a suitable receiver is compatible with your radio. As usual. I leave you. The receivers recommended and compatible with the radios recommended in the description of the video, but also in flight with issam puntoit. The connection is very simple: we have the black and red power cables, five times its bus and the yellow one, and as regards the antennas of the receiver, I made them pass inside the tp, iuele or supported.
It is simply with a shrinking thermo to prevent them from going inside the and there that I saw or that this quadcopter and very low cost. The cine did not even bother to configure beta flight on the flight controller and then let’s go and do it together. While we are there, we are going to leave the latest beta flight firmware. We see the firmware version. We write virgin here. Version 4.2.2 of beta flight is released as regards the board. It is called g. Fare f, 45. 105. We will need this name to leave the new firmware, and here we also have an error signal, because there is no basic configuration of the board let’s go to. Meanwhile, by writing status, see the hardware we have, and I point out that we have an active barometer. If we want to use a flight mode as a method, even a stabilized mode with a barometer could also be an idea for those who want to fly in sight and have a barometer stabilization or have fun flying with the barometer generally. Those who want fpv do not do it, but in any case we have the barometer. At this point, let’s bet let’s go on the firmware flyer and select make f 405, the latest stable version and 4.2.9 and then download the firmware from the internet and leave the firmware. At this point we have left the film. We do not go to configure the settings from zero to zero the settings and reset to factory settings.
So the first thing that asks me now to calibrate the accelerometer. I leave the quadcopter on a flat surface. I gauge the accelerometer and it is calibrated in this moment and we configure the ports on the first door. We have the ios b port that absolutely does not go disabled, otherwise we can no longer access. The quad will remember to change the settings again and on new art 1. There is nothing on. You are 2. We have to configure it as vtx tbs, smart audio to exit to command video sender via or sd to change, channel band and power directly or via computer or via radio via or sd. Then seeing the screen settings on hard 5. I honestly do not know what what is activated as msp. I do not know if this board also has bluetooth with speedy b. Probably yes! For this reason it remains activated by default and as regards the receiver and put on you are, if correctly I save and restart, I go to the general configuration. I personally do not want activate the barometer, not even the magnetometer, because there is not even the magnetometer in reality. In this board, we go ahead as a camera. I advise beginners to put 10 degrees so as to learn easily, and this mix was a little July together with the roll. So when we use the ‘oil, the quadcopter does not only turn but also tilts when cornering, and this helps a lot, especially for beginners the led streep.
We do not have it so we do not set it lermo. I like to activate it directly with the switch. So now we configure it so I take it off from here and with a very important thing to know about this quadcopter being also low cost and that it does not have a buzzer. So if they fall, you cannot make anything sound, nothing is heard and therefore we have to activate this rx loss function and x7. I put it on four that we have a different ringtone. What is this now, if I connect to the battery, you feel that the motors are ringing and it is a vibration which causes this sound. So if the quadcopter should lose signal and fall into tall grass, it will continue to sound. Until I hear it, I can recover it as regards the number 4 and the tone practically. Instead, if I activate rx set, I can activate or via the flight modes deactivate the sound via switch. We go on with the configuration the protocol of the if correct. Six hundred the motor stop, I activate it so the motors, even if they are armed, do not turn until I raise the gas or active lermo. We have no east sensor and the bidirectional shock cannot activate it on a former legislative decree regarding the maximum cocking angle of the motors, I put it at 180 degrees because so, if I had to go into a tree and s, I am at 180 degrees anyway.
I can arm the motors and maybe try to extricate myself and drop the quadcopter free it, and here we have finished the configuration, save and I go to the battery sensors and this four axis control panel with voltage sensor, but also current. In fact, now I disconnect the battery you see that the current drops to 0 attack on the battery the current rises to be calibrated. However, we have it here eventually, will change only the warning voltage of the cells to 3.3 v per cell and the rest. I leave as well as for the fail safe. If it does not appear. It means that you have not enabled the expert mode, however, leave it as it then drops and turns off the motors if it no longer receives the signal from the radio. As regards the setting up of the pilots is the standard beta flight that is just set for a 5 inch quadcopter of the kind. Then, eventually, if we need it, I will change it, and I will leave my configuration in the description as usual. Tion of the video as regards my kings should be more or less so then 0.85. As regards the arsi ray point: 85.80. 5. As regards the network. Instead, it is point 82, then eventually I change it and I leave you my configuration in the description of the video. Of course, the reits change a lot from one radio to another and they change just to have the same feeling with all the radios you have because some have a stick on greater excursion, others with less and these parameters you can get more or less the same Feeling here let’s do 0.
35 0.35. Then eventually, as I said, I change it as regards the average gas most likely. This will drop a lot maybe to 0.10, but I will verify this and then I will leave it to you in the description of the video. The same person responsible for the gas – I usually complain at 0.5, so for now I save and then change the filters do not change them. I leave them as they are and let’s see how this quadcopter flies. As regards the re cevente, and I have already armored, as you can see, they work well and I suggest you go and see how to configure the minimum and maximum limits on the radio in this video to configure this screen. While here the ars i band, I put it at 5 instead of the oil of the ben, I put it at 7. It means that if I move my stick slightly by five, especially the new gas stick slightly, the oil does not move anything. Ok, in fact, you can see that the quadcopter is stationary. Unless we move the stick. The flight modes are personal to you. I show what I configure with this arm the engine. I add another interval and new the switch, so it recognizes it directly. You see aux due if I put it automatically as soon as I move it. It recognizes it and we put with an angle so horizon always on the same switch and it will be in half the bie for the buzzer.
I usually put it on the same mode, switch that I move the stick to the central position here. The quadcopter starts to play, and now I configure lermo on same switch. So if I go ahead with the switch, the same switch in the bazaar, activates me lermo, so so buzzer is like this and harmon the typographer for crutchlow. I configure on this switch and we put it on the external position. So if I had to overturn the quadcopter fall to the ground, just go with this in this way, arm the motor and go right or left with the ski so as to overturn automatically. We save our configuration and check this way. I arm the motor you see that both are mason. We are in angle mode, step to horizon mode or step to acro mode. As you can see here, there is no acro mode, because if none of the stabilized modes is active, that is angle, ovo rises, a croke mode will automatically be active. The same also applies to bper and lermo. Now, in theory, we could configure ours or sd, but before doing it one important thing and configure the transmitters and video section that, as you can see, there is no table here. I and I have already configured a table suitable for this vtx with all the configuration you have to do is go up in flight with the sun, puntoit download it and then click on download file at this point, let’s load the file and, as you can see Here c ‘: it is the whole table with the powers etc.
etc. we save, and now we could change the channel band and also the power. Now, except here you see that it changes we return to our correct channel except and we are back the right. In fact, now I remove the camera and we can see ok, but I only put the cap back on to see better written and so at this point we can go to configure our or sd with the warnings we let ok, I use only one sd profile, So it will profile one and let the warnings add the vtx channel. As you can see, you positioned in this position and does not appear on the screen, and this is because the video format is automatically set and even if the declared format of the the camera. However, since it works, it is with them, so you have to select them and to exit to position the data correctly on the screen. In fact, now it is positioned correctly, we can add, possibly in milian per hour of the battery used let’s put them here. For example, we can add them if you want the flight mode. We reach here the throttle position and possibly that could be useful for beginners here is now zero and so and 50. So as to understand the throttle level. I used it very often with my students when we had the double command. I told him. A percentage of staying like 20 to 30 percent of percentage does not exceed kidney go down so as to start understanding how well the gas works.
Surely we will need timer number 2, what is timer number two, and this is practically the total time from when we have armed the quadcopter, and we put it here, as you can see, the sd of the focsiv really annoys me because it does not allow us To use the whole screen and it is useless, possibly if your receiver supports it on a channel, you can activate the rsi, but, as you can see, I do not have it so I cannot put it is the most important thing, of course, is the voltage of The total battery that I put up here at this point, except because we have finished the configuration and remember that it is a fundamental thing yes and do not import the correct table as regards transmitting video transmitter, you cannot change channel and band through or sd doing So with the sticks and going to vtx features and thus changing band and channel and even power eventually, but you ca, n’t, even see channel band and power on the screen as we did here. I hope this video was useful if it was click on like otherwise click on.